AIRTRONICS M12 Guia do Utilizador Página 61
- Página / 116
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
61
TR
Resetting the On-Time:
1) From within the SYSTEM menu, scroll UP or DOWN to highlight the INFORMATION
menu.
2) Press the ENTER key to open the INFORMATION menu. ON TIME > 00:00 (or
the actual Cumulative On-Time) will be highlighted and the current Firmware
version will be displayed.
The INFORMATION menu allows you to view the transmitter's current Firmware version, in addition to the transmitter's cumulative
On-Time in Hours and Minutes.
3) Press and HOLD the ENTER key to Reset the ON TIME to 00:00. Cumulative
On-Time will continue to accrue whether the transmitter is turned ON or if
only the Display is turned ON using the DISPLAY key. If Reset to 00:00 after
changing or recharging the transmitter batteries, it can be used to determine
battery discharge time.
EPA
SUB TRIM
REV
POINT AX1
POINT AX2
MOA MIX
4WS MIX
FEELING
F/S
B-F/S
LAP TIMER
INT1
INT2
PG. 62
PG. 63
PG. 64
PG. 64
PG. 65
PG. 66
PG. 67
PG. 69
PG. 69
PG. 70
PG. 71
PG. 73
PG. 73
MENU
PAGE #
MENU DESCRIPTION
Adjust Channel End Points to Balance Servo Travel
Adjust Servo Centering to Center the Servo Horns
Change the Direction of Servo Travel
Adjust Auxiliary 1 Point Values to Change the Servo Stepping Behavior
Adjust Auxiliary 2 Point Values to Change the Servo Stepping Behavior
Adjust and Change Dual Motor Mixing options (Crawler Car Types Only)
Adjust and Change Four Wheel Steering Mixing Options (Crawler Car Types Only)
Adjust Steering and Throttle Channel Latency Values
Program Fail Safe Settings
Program Receiver Battery Fail Safe Settings to Ensure Optimum Servo Performance
Program the Lap Timer Goal Time, Pre-Alarm and Lap Timer Start Options
Program Interval Timer 1 and Change its Start Options
Program Interval Timer 2 and Change its Start Options
The following Programming Menus are available within the SETUP menu:
To access the various SETUP Programming Menus, turn the transmitter ON, then
press the SELECT switch to highlight the SETUP menu. Press the ENTER key to
open the SETUP menu.
Scroll UP or DOWN to highlight the desired Programming Menu, then press the
ENTER key to open that menu.
Depending on the Car Type chosen, some Function Programming Value
Names may differ from those shown in this section.
- 1
- 2
- 2
- Troubleshooting Guide 3
- - = Negative (Black) 4
- + = Positive (Red) 4
- S = Signal (Blue) 4
- 5
- 5
- 5
- 6
- 6
- 7
- 7
- 10
- 10
- Diagrams 11
- Transmitter 11
- Battery Charging Options 11
- Transmitter Overview 11
- CURVE Menu 12
- VR ADJUST Menu 12
- 13
- Steering 15
- BOOT Menu 17
- Screen Overview 17
- Display Screens Overview 20
- LOG SETUP Menu 21
- Viewing Lap Times 21
- Telemetry Data Recording 22
- BIND Menu 23
- Model Select 29
- 31
- 35
- POINT AUX 1 Menu 41
- POINT AUX 2 Menu 41
- CODEAX1 and CODEAX2 Menu 41
- 42
- 45
- 45
- 47
- TELEMETRY Screen Overview 48
- 49
- MODE menu 54
- 57
- 57
- INFORMATION Menu 60
- SUB TRIM Menu 62
- Changing 63
- Servo Sub-Trim Values 64
- AUX TYPE Menu 64
- ASSIGN Menu 67
- REV Menu 68
- Changing 70
- Choosing Fail Safe Settings 71
- 72
- TRIGGER > 74
- EPA Menu 76
- TRIM TYPE Menu 77
- 79
- 83
- 83
- Changing the Switch Mode 84
- 90
- R-MODE Menu 94
- Service and Support 97
- FUNCTION 99
- 101
- 106
- See also 107
Manuais e produtos relacionados com Controlos remotos AIRTRONICS M12
Controlos remotos AIRTRONICS MX-V Guia do Utilizador
(24 páginas)
(24 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais